This is not a limitation of our disc, just what all discs and pattern generators must deal with. In fact, with the interview we did at CES with Phil, I made a point of not wanting to call it a calibration disc for reasons you mention. (Same as CalMAN) For HDR10/10+, no such metadata like Dolby. The add-on will have Dolby Vision 4.0 pattern that can also turn off tone mapping. LG is the only display so far where tone mapping can be disabled via CalMAN calibration. The issue with most HDR displays is that you are going to fight tone mapping while doing this. You can adjust CMS and white balance / grayscale. Sony is also unique in that the SDR calibration must be done first since HDR is based off of that. 4000 nit content to get the most out of both w/o clipping.
There are some users now creating different settings for 1000 vs. Sony is the exception so far, at least the Z9D. You should not touch contrast on most HDR displays because of what you describe. Or am I completely off the friggin' reservation about all this? In other words, if we're supposed to keep, say, Backlight and Contrast at maximum in HDR for the display to tone map properly and all that, what is this disc providing us - is it more getting the Color correct with HDR or perhaps Sharpness? However, with HDR/4K, what are discs such as this new S&M supposed to be "calibrating" when it comes to HDR.or is it more of a "measurement" system to see how a display or projector is performing? For example, you need exactly 3.12 meters.
#Spears and munsil 3 movie
I totally get the logistics behind SDR calibration (in the past, I've used the Spears and Munsil Blu-ray setup disc that came in the box with my Oppo BDP-83 plus some other tools to adjust my Sony SXRD rear projection set, though the S&M disc was WAY over my head), and, to be honest, with my current display, a Samsung NU8000, just switching it into its Movie mode and making some adjustments to Local Dimming, Digital Clean View, Backlight and Auto Motion Plus provided a really nice image out of the box (I still run it this way with no tweaks). Spears & Munsil UHD HDR Benchmark Spears & Munsil HD Benchmark Harkwood Services Ltd Sync-One2 v2. I'm a bit foggy when it comes to "calibrating" for HDR - we've been told over and over again (at least I've read it over and over) that once a display switches into its HDR mode (Standard, Movie, whatever), we should pretty much leave settings alone as chosen by the manufacturer as defaults because these are supporting the tone mapping process (in other words, Backlight should be left at maximum as well as Contrast, while Local Dimming systems on LCDs should be on their highest setting, et al.). In the worst case, detach the bottom.Please forgive me if this was covered somewhere by another member in the thread, but. If none of the above apply, you can probably put lights on 4 sides.
#Spears and munsil 3 tv
Better to omit lights.Ĥ sides are best when the TV is on a wall mount, but you can't really go wrong with 3 sides. Reflections - If the TV is on a glass tabletop or directly above (within 4-5 inches) a glossy soundbar or center channel speaker, it's probably going to cause glare. Another example is a sound bar or center channel speaker directly below the TV (directly means virtually touching all the way up to a few inches below).ĭistractions - like a mess of wires or a bunch of stuff under the TV (set-top boxes, vases, framed photos, etc). Obstructions - like a TV on a stand when there is nowhere for the light to pass below the TV.
Generally speaking, you should put lights on only 3 sides when you have any of the following: You could round down to 3 meters in this case, but you’d want to place lights ever-so-slightly further from the edge than the recommended 2 inches.
#Spears and munsil 3 update
Hopefully it will be fixed with a future FW update to all UHD BD players. Basically there is a bug that will reduce the quality in player-led. Please note that you will not be placing the strips 2” from the edge, but using the “inverted-U” shown on our installation page. Its okay if your TV only supports player-led (DV Low Latency), the player will fall back to player-led in that case.
0 kommentar(er)
